A range of top quality wading boots combining grip, durability and light weight.
Our design solves this problem in a simple, unique way. By re-shaping the rubber mid-sole in the toe area, it allows the sole to sweep up, hence avoiding rocks and pebbles when wading or walking in rough terrain.
Re-shaped mid-sole
One of the biggest problems with all makes of wading boots is soles becoming detached. This can be due to many causes, but the most common, is the sole coming away around the toe, due to the constant ‘stubbing’ against rocks, which wading boots have to endure.
Stream-Trek 13080-04 XS-Tra Grip Rubber Sole with Studs
Our range combines all the features the serious angler would hope to find in a top-quality wading boot. The rugged construction combines a 1200D nylon material, with a PU synthetic Nubuck, to provide maximum support and protection. The reinforced rush rubber toe cap and heel, provide additional support and helps protect the uppers, to avoid chafe on rocks.
Available in two sole options: Our popular XS-tra Grip Rubber sole with replaceable metal studs.....
Sizes: 7, 12 Out of stock
Stream-Trek 13080-07 Combi Studded Felt/Rubber Sole
.....or our popular XS-tra Grip Rubber sole with replaceable metal studs or our combination felt sole. This unique sole has rubber toe and heel sections for extra wear plus studs built into the felt for additional grip. The felt sole is not only stitched right through the mid-sole, but is also cut at an angle front and back, neatly ‘dovetailed’ under the toe and heel pads, to ensure the felt cannot become detached from the boots.
With the huge increase in ‘rock-fishing’ for Bass, Pollack and Wrasse, our range of Rockhopper boots and accessories give you the edge!
Our Spike Sole consists of hardened steel spikes, set between deep rubber ‘cleats’ so they are able to ‘flex’, which is what gives them their outstanding grip. We haven’t yet found a surface this sole will not grip on – even ice!
The flexible, hardened steel spikes cut down through the weed, to grip the rock below and will even grip in icy conditions. Neoprene uppers with a side zip closure they are equally suitable for ‘wet wading’ in the summer months or overseas.
Please note: For use over stockingfoot waders, we recommend you go up one size on your normal shoe size.
Can be used on any waders or wading boots for additional grip on slippery surfaces,whether algae covered rocks, dam walls or even ice! Simply fasten the wader-grips to your boots for instant, extra grip. The thermoplastic rubber material is highly elastic, so they will stretch to fit a wide range of boot sizes. Ideal for walking long distances to fish (so wants cleated soles), but also extra grip in the river or reservoir bank or rocky shoreline.
Available in sizes:
L – for all standard shoes, boots or waders up to size 9 (EU 43)
XL – for all shoes, boots, wading boots, or waders from sizes 9-11 (EU 43–45)
XXL – for all shoes, boots, wading boots, or larger waders and thermal boots, from sizes 11-15 (EU 45–50)
Remove the “silent wading” rubber cap & you have a hardened steel tip for extra grip & it comes with an optional screw on ‘tip-cup’ to spread the load in soft sand, mud or snow. Ergonomic rubber handle grip, with adjustable wrist strap & detachable, elasticated lanyard.
An updated version of our original model, but marked with depth markers up to 140cm. Useful for when you need to know if the next step could be out of your depth. Also allows quick and easy measurement of catch & release salmon.
A tough, practical wading staff made from anodised aluminium. Telescopes down from a maximum 63” to a convenient 34” for travelling. The Twist & Lock mechanism allows it to be locked at any required length. Weighted foot with rubber grip. Rubberised handle with adjustable lanyard & clip.
Manufactured to our own, exclusive design, our new heavy duty zinger can be used with large nets, such as Salmon zinger can nets, as well as wading staffs. The 54” Kevlar cord can be locked at any position, so a wading staff or landing net is always attached to you, but at a convenient distance.
If like many anglers, you suffer from an aching back after a full days fishing, our Lumbar Support Belt is the answer. The 2” wide webbing belt has a quick release plastic clip and buckles, allowing adjustment from 34” to 51”. The rear lumbar pad has 1” thick contoured neoprene, inside a Nylon cover, to provide pressure and support, just where it’s needed.
A hard plastic Stripping Basket so popular with saltwater and reservoir anglers. Lightweight, with adjustable waist belt and neck support strap. Tapered line control turrets in the base, to prevent fly lines tangling.
An optional extra for our Stripping Basket is this set of 10 plastic spikes, which fit into the top of the turrets. Not only do they stop water slopping up the turrets and filling the basket, but their soft, flexible construction helps tame fly line coils when shooting and reduces tangles. These will fit all brands of Stripping Basket of this same design.
The best line tray design on the market. Mesh base with a fold down base board which holds the tray open when in use and prevents water filling the tray from below and tangling the line, when deep wading or saltwater fly fishing. Folds flat against your body when not in use. Adjustable webbing belt with quick release buckles. Velcro pocket inside, to take leaders etc.
3mm double-lined Neoprene. Heavy-duty zip, plus Velcro flap fastening. Worn over the top of wading boots, to prevent gravel and sand entering the boots.
Designed specifically for saltwater wading, eliminating the conventional zip fastening, prone to jamming when wet wading on sand. The Velcro compatible material allows the gravel guard to wrap securely around your leg and secure in any position, completely preventing fine sand and gravel entering your wading boots. Lacing hook attaches to boots to hold them in place.
Super-hard, screw-in Wader Studs, with a 4-point Tungsten Carbide tip for the ultimate grip on slippery rocks & pebbles. The grade 304 stainless steel screw has high corrosion resistance, while the Tungsten Carbide head is 30% harder than the highest grade of hardened steel. Easily screwed in to boots or waders, with the Stud Tool provided.
Super hard, zinc plated steel studs, give additional grip to felt or cleated sole waders. Our model has a deeper head for extra grip and longer wear-life. Easily screwed in with our optional Stud Socket or a Phillips screwdriver.
Our range of Stormsure products, covers every possible type of wader, boot and clothing repair or adhesive application.
SST Stormsure Adhesive
The original adhesive and sealant for all types of repair in waders, boots and just about anything else you can think of. We even use this to re-stick felt soles!
This Cyanoacrylate based super-glue bonds in seconds and can be applied to a multitude of fishing applications, binding all types of materials, fly dressings, leaders, rod whippings etc.
New from Stormsure – tough, self adhesive, clear PVC patches, providing quick and easy repair to waders, jackets, boots etc. Stick to just about anything, even when wet!
This water based, air-dry proofer and re-proofing spray is easy and quick to use and requires no ‘pre or post treatment’. Just clean the fabric of any dirt or mud, apply and allow to dry. Turns any fabric waterproof, by applying a DWR (Durable Water Repellent) coating to the surface. Ideal for re-proofing any garment, waders, tent, bivvy or umbrella, which has started to leak.
Leak-Detector will find those annoying little pin-prick leaks in breathable fabric quickly. Simply pump-spray the Leak-Doctor over the suspect area and any leaks will appear as small, dark patches in no time. Quickly repaired with Snowbee Suncure, Stormsure or our Pocket Repair Kit, to get you back fishing fast!
A revolutionary material EXCLUSIVE to Snowbee that transforms wader repair! A flexible, clear repair material cured by UV light. Suncure is totally cured in 15 seconds (in high UV conditions). With Snowbee Suncure a lost day's fishing due to damaged or leaking waders is a thing of the past!
Specifically designed for replacing Felt-Soles on waders or wading boots. The one-piece felt sole is oversize to fit any size boot up to size 14. Simply cut down to fit smaller sizes. Includes adhesive,replacement felt-soles and full instructions.